Sae j744 pdf

Sae j744 pdf

Rating: 4.6 / 5 (4366 votes)

Downloads: 10326

CLICK HERE TO DOWNLOAD

.

.

.

.

.

.

.

.

.

.

2 normative references the following normative documents contain provisions which, through reference in this text, constitute provisions of this part of iso 3019. get the hydraulics knowledge you need! sae j744 revised jun96 figure 1— dimensions of 2 and 4 bolt pump and motor mounting flanges 4. plugs tightening torque: 20- 25 nm. the direction of rotation of the motor depends from direction of delivery oil as shown in the picture below. ordering code ( sae) example: f1- 61 - r f1 frame size 25, 41, 51 or 61 shaft rotation r right hand l left hand standard sae versions designation ordering no. available from sae international, 400 commonwealth drive, warrendale, pa, tel: inside usa and canada) oroutside usa), www. 2 shaft identification codes are found in tables 2, 3, and 4 and figures 2 and 3. society of automotive engineers [ sae] pdf price. note involute spline is in accordance with sae j744 [ 1]. sae jb- b) r splined shaft 1 in 15t 16/ 32 dp sae jb- b) u splined shaft 7/ 8 in 13t 16/ 32 dp sae jb) w splined shaft 7/ 8 in 13t 16/ 32 dp sae jb) 1) ansi b92. a – sae j744 82– 2 ( sae a) b – sae j744 101– 2 ( sae b) c – sae j744 127– 2 ( sae c) series designation ( frame size) 45vpft – 140 to 195 cm3/ r ( 8. 100 mm b 2- bolt flange spigot dia. 2 the number following the dash ( — ) is arbitrarily. amendments & corrections. content provider. 75 in keyed shaft) 06 – sae j744 44– 4 ( d splined shaft) shaft. hydraulic pump and motor mounting and drive dimensions. the spacer ring will. this sae standard applies to hydraulic pumps and motors used on off- road self- propelled work machines as described in categories 1 through 5 of sae j1116. f1- 25- rlf1- 41- rlf1- 51- rlf1- 61- rlinstallation dimensions, f1- 25, - 41, - 51. splined shaft sae jt c d sae jt c p sae jt r r parallel keyed shaft sae jshort version) r, c q front cover 09 rectangular flange spigot dia. available for subscriptions. 12 = sae “ d” splined 13 tooth ( j/ 16 d. the purpose of this standard is to provide a progression of standard mounting flanges and shafts that are dimensionally compatible. sae j390 dual dimensioning engineering drawings sae j1116 categories of off- road self- propelled work machines. “ hydraulic pump and motor mounting and drive dimensions”. 3 = sae “ cc” splined 17 tooth ( j/ 24 d. this sae standard applies to hydraulic pumps and motors used on off- road self- propelled work machines as described in categories 1 through 5 of sae j1116 jun86. pump mounting plates – sae j744 dimensional data spacer rings spacer rings are available for all sae bell housing sizes ( 1, 2, 3, 4, 5, 6). sae744- hydraulic pump and motor mounting and drive dimensions- this sae standard applies to hydraulic pumps and motors used on off- road self- propelled work m. 1 the number preceding the dash ( — ) is an approximation, in millimeters, of the shaft major diameter. 6 mm sae jb) c 2- bolt mounting spigot dia. for dated references, subsequent amendments to, or revisions of, any of these publications do not apply. sae tsb 003 rules for sae use of si ( metric) units. connect the drain line before using the motor. just to determine what flange and shaft of pump or motor you have, please see below excerpts from the next standards: sae j744. sae pump and motor mounting flange and shaft dimensions. 1) bsp- to- sae adapter ( included). a – sae j744 127– 2 ( sae c) b – iso 3019/ 2 125a2hw c – sae j744 152– 2 ( sae d) d – iso 3019/ 2 160a2hw shaft type 01 – sae j744 38– 1 ( 1. the purpose of this standard is to provide a progression pdf of standard mounting flanges and shafts that are dimensionally. “ dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors”. use always the upper drain port according to the motor position and in any case always use the drain port that can ensure the casing being filled- up. 1a- 1976, 30° pressure angle, flat root side fit, flank centering, tolerance class 5 k parallel with key iso. 13 = sae “ c straight ( jkeyed 16 = sae “ d“ straight ( jkeyed blank = non- thru- drive ( single pump) a = thru- drive pump with sae “ a” 2- bolt rear flange mounting ( sae jb = thru- drive pump with sae. sae straight ( keyed) shafts. industrialhydrauliccontrol. we have no amendments or corrections for this standard. this sae standard applies pdf to hydraulic pumps and motors used on off- road self- propelled work machines as described in sae j1116. 52 mm with o- ring m port. 55 mm sae ja) r spigot dia. this sae standard applies to hydraulic sae j744 pdf pumps sae j744 pdf and motors used on off- road self- propelled work machines as described in categories 1 through 5 of sae j1116 jun86. publication date. the rings provide additional space standoff from the engine flywheel housing and the pump mounting spacer plate. 50 in keyed shaft) 02 – sae j744 38– 4 ( c– c splined shaft) 03 – iso 3019/ 2 e40n ( 40mm keyed shaft) 05 – sae j744 44– 1 ( 1.