En 10131 pdf

En 10131 pdf

Rating: 4.6 / 5 (1607 votes)

Downloads: 71154

CLICK HERE TO DOWNLOAD

.

.

.

.

.

.

.

.

.

.

tolerances on dimensions and shape is classified in these ics categories: 77. the tolerances on width of flat products in low carbon and high yield strength steels are given in 7. buy din en 10131: - 09 cold rolled uncoated and zinc or zinc- nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - tolerances on dimensions en 10131 pdf and shape from intertek inform. en10131_ dimensions and flatness - free download as pdf file (. the concerned standards are en 10130, en 10152, en 10271, en 10209, en 10268 pren 10336 and pren 10338. scribd is the world' s largest social reading and publishing site. grain- oriented magnetic steel sheet and strip ( en 10107) ; cold rolled electrical non- alloy and alloy steel sheet and strip delivered in the semi- processed state ( en 10341) ; cold rolled uncoated low carbon and high yield strength steel flat products for cold forming ( en 10131) ; cold reduced blackplate ( en 10205). ( 1st edition) standards for steel are changing constantly, and many national standards have been replaced by european standards. standard number: din en 10131. standard by din- adopted european standard,. en冷成形用冷轧无涂层、 电镀锌或锌- 镍涂层低碳高屈服强度扁平制品－ 外形和尺寸偏差ch. specifies the en 10131 pdf design, manufacture and construction of above- ground storage tanks not exceeding a capacity of 85 m3. it does not apply to cold rolled strip ( rolled width 600 mm) or to flat cold rolled products for which there is a specific standard, in particular the following: cold rolled non- grain oriented magnetic steel sheet and strip ( en 10106) ; semi- processed steel strip for the construction of magnetic circuits ( en 1015) ; tinplate and eccs. this special edge camber tolerance is. view all product details. actual width of the sheet. the out- of- squareness shall not exceed 1% of the. bs en 10131: is maintained by ise/ 109. 3 for slit wide strip of width less than 600 mm. the project applies to cold rolled uncoated and electrolytically zinc ( en 10152) or zinc- nickel coated ( en 10271) low carbon and high yield strength steel flat products for cold forming with a minimum thickness of 0, 35 mm and, unless otherwise agreed at the time of ordering, less than or equal to 3 mm thick, delivered in sheet, wide strip, slit. scope: this european standard applies to cold rolled uncoated and electrolytically zinc or zinc- nickel coated low carbon and high yield strength steel flat products for cold forming with a minimum thickness of 0, 35 mm and, unless otherwise agreed at the time of ordering, less than or equal to 3 mm thick, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide. name: cold rolled uncoated and zinc or zinc- nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - tolerances on dimensions and shape. bs en 10131: this standard bs en 10131: cold rolled uncoated and zinc or zinc- nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming. txt) or read online for free. en, designation systems for steels part 2: numerical system en 10049, measurement of roughness average ra and peak count rpc on metallic flat products en 10079: 1992, definition of steel products en 10131, cold rolled uncoated and zinc or zinc- nickel electrolytically en 10131 pdf coated low carbon and high yield. status: standard. pdf), text file (. 2 for sheet and wide strip and in 7. 50 flat steel products and semi- products. 2 normative references. din en 10131 cold rolled uncoated and zinc or zinc- nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - tolerances on dimensions and shape; german version en 10131:. for slit wide strip of width less than 600mm a special edge camber tolerance ( cs) of 2mm maximum on a 2 metre length may be specified. für die aufgeführten technischen lieferbedingungen nach en 10130 und en 10152 gilt folgende maßnorm: en 10131 kaltgewalzte flacherzeugnisse ohne überzug und mit elektrolytischem zink- oder zink- nickel- überzug aus weichen stählen sowie aus stählen mit höherer streckgrenze zum. for lengths less than 2 metres, the edge camber shall not exceed 0. this standard is available from the following sources: bsi knowledge british standards online ( bsol) other historical versions of this standard document also exist: bs en 10131: 1991 [ current until ]. 内容提示： en 10131: ( e, ) i 前 言 本文档 ( en 10131: ) 由秘书处设在ibn的eciss/ tc 13“ 冷作扁平产品－ 质量、 尺寸、 偏差及规定试验” 技术委员会编制。. tolerances on width general. enfree download as pdf file (. en 10051 defines five categories: • table 2: hot rolled low carbon steel sheet/ plate and strip for cold forming • category a: r e ≤ 300 mpa • category b: 300 mpa < r e ≤ 360 mpa • category c: 360 mpa < r e ≤ 420 mpa • category d: 420 mpa < r e ≤ 900 mpa tolerances on thickness according to en 10051 table 2. pdf) or read online for free. 最迟于年1月. there are now so many essential steel standards that the contents of this hand- book have, for reasons of space, been split between the printed book and the cd- rom. width is measured perpendicularly to the longitudinal axis of the product. 3% of the actual length. it does not apply to cold rolled strip ( rolled width < 600 mm) or to flat cold rolled products for which there is a specific standard, in particular the following: - cold rolled non- grain oriented magnetic steel sheet and strip ( en 10106) ;. din enfree download as pdf file (. breather pipes, bulk to agriculture tank ( bta tank), bulk to farmer tank ( btf tank), bund walls, bunding, installation, liquid fuels, petroleum products, pipework systems, skid tank, tanks ( containers), vent pipes. din- en- 10131 cold rolled uncoated and zinc or zinc- nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - tolerances on dimensions and shape; german version en 10131:. en 10131: ( e) 7 7. bs enfree download as pdf file (.