Washing Machine Repair Dubai

Why is My Dryer and Washing Machine Producing Noise?

There are many reasons why your dryer or washing machine might be making noise. You could have a faulty inlet valve, an idler pulley, or even a drum bearing. Whichever is causing the noise, it is important to have it looked at immediately.

We provide a complete range of Washing Machine Repair Dubai Service, with experienced experts.

Drum bearing

If you have a noisy dryer or washing machine, there may be a problem with your drive belt or bearings. The drum bearings are used to support the drum as it turns, and may fail if they are worn out.

To check if your dryer is running on a faulty drive belt, it is best to remove the front panel and look for signs of wear. Depending on the model, you will find a variety of signs.

Some of the more common signs include cracking and fraying. You will also find wear on the idler pulley, which is a device that automatically tensions the drive belt. It is likely located on the front right side of the dryer.

Another sign of an ailing drive belt is a loud squealing sound. This may be caused by a broken pulley wheel, but is not always the case.

Typically, the most obvious sign of a faulty drive belt is that the drum will not turn. You can test this by manually spinning the drum, and see if it makes a difference.

For dryers that use a belt to rotate the drum, you will need to remove the belt to get access to the rollers. If you have an electronic dryer, you will also need to check the circuit board. Any burn marks or shorts on the board could prevent the dryer from starting.

Finally, you may need to replace the belt itself. Sometimes, this is a small, and inexpensive job. Otherwise, a new drum kit and bearings will be necessary.

A bad or cracked drum spider is another common culprit. A damaged spider can cause a banging sound when the drum spins. However, a cracked spider can also break off and corrode the drum.

Before repairing any appliance, you should consider getting professional help. They can also take care of the bra wire, which may have become stuck inside the drum.

Lastly, if your dryer is hardwired, you may need to hire a repairman for the same. While these appliances are fairly simple to service, you may want to take advantage of a professional to save yourself time.

Faulty inlet valve

A faulty inlet valve can result in no water at all, low water pressure or flooding during the wash cycle. There are several ways to diagnose this problem. However, if you are unsure what to do, a professional repair service may be your best bet.

The main reason an inlet valve fails is usually due to a clogged filter screen. This screen is a fine mesh material designed to prevent debris from entering the system. As this screen ages, it will gradually begin to clog. If you do not replace the filter, it will slowly build up to the point where the machine will not fill with water.

The water level pressure switch, which is located behind the control panel, is the best way to detect a faulty inlet valve. It works by sending an electrical signal to a gate that opens and closes. When this is done correctly, the washing machine will fill with the proper amount of water.

Depending on the model, you may need to open the front or back of the washer cabinet to access the inlet valve. To safely pull out the washer, make sure there is a spot where you can stand and work. Also, have a bucket to catch any supply hoses that come out the top of the machine.

Alternatively, you can disconnect the power from your appliance and turn off the water. You will need a pair of pliers to loosen the hose clamps and then unhook the hoses. In some cases, you will need a flashlight to check the ports on the inlet valve.

Lastly, you can check the continuity of the water level switch using a multi-meter. It can be tricky to do this, though. Your repair specialist should know this information or you can take a stab at it yourself.

Another way to tell if your inlet valve is in need of repair is to try running a test cycle. If you see any water flow through the tub during the cycle, you should consider having the inlet valve replaced.

For the best results, a repair professional is your best bet. They will have the equipment to diagnose your inlet valve and repair it.