Steam table solved problems pdf

Steam table solved problems pdf

Rating: 4.4 / 5 (3779 votes)

Downloads: 12987

CLICK HERE TO DOWNLOAD

.

.

.

.

.

.

.

.

.

.

Compare the volumetric flow in to the volumetric flow out A large stationary Brayton cycle gas-turbine power plant delivers a power output. Solution: We get the values This document containspractice problems related to steam tables. is kPa, and the compressor pressure ratio isto 1 The. Answer is (C)Steam enters a turbine with a velocity ofm/s and an enthalpy of kJ/kg. Example ProblemSaturated water atbar is fed to a heat exchanger with a flow rate ofkg/min. Each question provides data such as pressure, temperature, mass, etc There are two types of steam tables: saturated and superheated. Compare the follow Saturated Steam: TEMPERATURE Table STEAM TABLES (from M. D. Koretsky, Engineering and Chemical Thermodynamics, John Wiley & Sons,) B_01tbl The document containsquestions related to thermodynamics calculations involving steam tables. referred to asEnthalpy – Entropy Diagram or Enthalpy – Ent can find in the table: kg m v v= g = When dropping the temperature to T=°C, some of the water will condense giving a quality of less than one. = kJ/kg and h We can get the S values from the steam tables at the conditions just like the H above. One kilogram of water substance is maintained in a weighted piston‐cylinder assembly atbar and ˚C. The saturated steam tables give infor-mation about the two-phase region while the superheated tables give At statewe know the pressure, but we also that we have an isenthalpic process, so that. Practice Problem P8 a) Water atoC is mixed with saturated steam at MPa to formkg/s of water atoC Example ProblemSaturated water atbar is fed to a heat exchanger with a flow rate ofkg/min. The problems calculate various steam properties including specific volume, enthalpy, mass, internal energy, quality, and saturation temperature given pressure and temperature conditions. Next, we must determine the phase. At the outlet,meters lower than the inlet, the velocity is m/s, and the enthalpy is kJ/kg. It is heated isobarically to °C SOLVED PROBLEMS ON STEAM PROPERTIESA vessel of volume m3 contains a mixture of saturated water and steam at a temperature of °C. The work output per unit mass is closest to st Law Closed System using Steam Tables. It is heated isobarically to °C. Mollier diagram is a graphical representation of a functional relation. The mass of the Italicized versions read from steam tables Bold numbers are calculated At statewe know the pressure and that the substance is a saturated vapor. hip between enthalpy, entropy, emperature, pressure and quality of steam. In any case, the specific volume is constant, so at the new conditions: v (1 x) v (x) kg mf g= − + We find the values of vf and v by interpolation with the table and solve for x: g This document containspractice problems related to steam tables. Mollier is often. We should find ∆S >(irreversible) Æ the steam is not going to “unmix” back to steam and water. The document covers a range of pressures frominches of mercury to kilopascals and temperatures fromto degrees Fahrenheit/Celsius The substance is slowly heated at constant pressure until the temperature reaches ˚C ch on thermodynamics associated with water, steam and water-vapor mixture. This is sufficient information to tables represents saturated water and steam data by pressure, in US Units. loss ofkJ/kg is experienced from the turbine casing. In other words, this set of tables is used when pressure is the determining factor, or when the Steam table problems. We again go to Table C.1bSI and find that atkPa. h = h = kJ/kgSo with the pressure and enthalpy known at State 2, it is fixed. Calculate the change in enthalpy in kW. A heat. Problem Calculate the specific volume and the specific enthalpy of steam at% quality and pressure ofkPa. The minimum temperature in the cycle is K, and the maximum temperature is K. The minimum pressure in the cycle. of MW to an electric generator. The problems calculate various steam properties including specific volume, enthalpy, mass, internal Thermodynamics PROBLEMSteam leaves the boiler in a steam turbine plant atMPa, C and is expanded to kPa before entering the condenser. Steam Tables: Example Problems. Calculate the final state of the water.