Iso 13337 pdf

Iso 13337 pdf

Rating: 4.9 / 5 (7388 votes)

Downloads: 42303

CLICK HERE TO DOWNLOAD

.

.

.

.

.

.

.

.

.

.

iso 13337: specifies the characteristics of slotted spring- type straight pins, made of steel or of austenitic or martensitic stainless steel, light duty, with nominal diameter from 2 mm to 50 mm inclusive. 02649 d bef br brazil 0. iso 13337 ~ dinhv bn 878 slotted spring pins light duty steel hardenedhv black • ~ uni 6874 • ~ csn 022156 article# d1 d1 min. 6484 q aud at austria 0. double shear is not specified for 300 series stainless steel. spring pin iso 13337 – 6 × 30 – pdf st example 2 a martensitic stainless steel ( c), non- interlocking slotted spring- type straight pin ( n), light duty, with nominal diameter d 1 = 6 mm and nominal length l = 30 mm is designated as follows: spring pin iso 13337 – 6 × 30 – n – c ` ´ ` ˆ` ˜ ` ¯ ` ˘ ` ˙ ` ˙ ` ˙ ` ¨ ` ˚ ` ˘ ` ¸ ` ¸ ` ¨. iso 13337: ( e) pdf disclaimer. this pdf file may contain embedded typefaces. risk management — vocabulary management du risque — vocabulaire international standard iso 31073 first editionreference number iso 31073: ( e). 1 scope this international standard specifies the characteristics of slotted spring- type straight pins, made of steel or of austenitic or martensitic stainless steel, light duty, with nominal diameter, d 1, from 2 mm to 50 mm inclusive. for information only. © vogelsang fastener solutions, inc. this international standard specifies the characteristics of slotted spring- type straight pins, made of steel or of austenitic or martensitic stainless steel, light duty with nominal diameter, d 1, from 2 mm to 50 mm inclusive. iso and not the mmus. 197355 q brl ca canada 0. each member body interested in a subject for which a technical. stift elastic, crestat. spring- type straight pins — slotted, light duty. non- governmental, in liaison with iso, also take part in the work. pins 13 through 50 m nominal diameter also available. iso 13337: 1997 spring- type straight pins - slotted, light duty. 077658 d ats be belgium 0. this second edition cancels and replaces the first edition ( iso 13337: 1997), which has been technically revised. s l, 3 1, 9 0, 2 0,. when those changes occur, the rto or iso may need to change the data being. mounting hole nominal diameter tolerance zone is hi 2. metric series- isoformerly din 7346) metric pins 8mm and smaller diameter double chamfer is standard ( see top chart) metric pins over 8mm in diameter single chamfer is standard ( see bottom chart) * iso 13337 pdf * in individual cases, it is important to check whether these shear forces can be taken into account depending on the structural properties. iso 3269, fasteners — acceptance inspection iso 4042, fasteners — electroplated coatings iso 6507- 1, metallic materials — vickers hardness test — part 1: test method iso 8749, pins and grooved pins — shear test 3 dimensions see figure 1 and table 1. iso collaborates closely with the international electrotechnical commission ( iec) on all matters of electrotechnical standardization. iso shall iso 13337 pdf not be held responsible for identifying any or all such patent rights. country/ union rate ind cur code ; au australia 0. measure length from end to end. click here to purchase the full version from the ansi store. full description. therefore, any associated burden is counted as a burden on rtos and isos. iso 377: ( e) foreword iso ( the international organization for standardization) is a worldwide federation of national standards bodies ( iso member bodies). iso 13337 is similar to din 7346. ics code ( pins, nails) : 21. a for slotted spring- type straight pins with a nominal diameter d. scope: this international standard specifies the characteristics of slotted spring- type straight pins, made of steel or of austenitic or martensitic stainless steel, light duty, with nominal diameter, d1, from 2 mm to 50 mm inclusive. while the ongoing delivery of data under ferc– 921 is continuous and routine, each rto or iso makes sporadic changes to its individual market with commission approval. this is a preview of iso 13337: . international standards are drafted in accordance with the rules given in the iso/ iec directives, part 2. din 7346 - dowel pins, light version current norm: din en iso 13337 equivalent norms: iso 8752; csn 022156; uni 6874;. purdue mep truly partnered with jaeger- unitek to provide a complete and comprehensive iso 50001 certification and training package. through the diligent efforts and guidance from purdue mep, jaeger- unitek was able to fully secure a state- funded grant to help cover almost all of the funding to cover all of the activities. note the nominal diameters have been chosen in such a way that pins can. spring- type straight pins, light type. iso 13337 slotted spring pins light duty both ends are chamfered on pins less than 10 mm in diameter; only one end may be chamfered on 10 mm and larger diameter pins. also known as roll pins. the work of preparing international standards is normally carried out through iso technical committees. goupilles cylindriques creuses, dites goupilles élastiques — série mince. iso 13337 was prepared by technical committee iso/ tc 2, fasteners, subcommittee sc 10, product standards for fasteners. double shear is only applicable to carbon and 420 stainless steel.